低阶煤热萃取物与瘦煤共炭化焦炭的微观结构及显微强度研究

以众唯瘦煤作为主炼焦煤,大同长焰煤萃取物作为添加剂,进行共炭化处理制备坩埚焦。利用偏光显微镜法定量研究焦炭光学显微组分,获得焦炭的各向异性指数(DRAS);采用XRD及分峰拟合的方法研究了焦炭的微晶粒径(L_c)、芳香缩合度(I_a)、石墨化度(g);利用Raman光谱结合分峰拟合的方法研究了焦炭中理想石墨微晶含量(I_g)。对所得焦炭的光学显微组分进行定量分析发现:大同长焰煤热解萃取产物的添加对共炭化焦炭的光学显微组分有显著的影响,利用偏光显微镜法计算出焦炭的DRAS与XRD和Raman计算的焦炭微晶参数呈现很好一致性。并且,焦炭的显微强度与其微观结构关联性极大。     

基于炼焦煤族组成和结构参数的焦炭质量预测模型及其成焦机理

以五种炼焦煤和44组配合煤为研究对象,在40 kg小焦炉环境下完成煤杯炼焦实验,以煤全组分分离所获得的煤重质组、密中质组和疏中质组收率Y_(HC)、Y_(DMC)、Y_(LMC)及反映煤中氢键缔合情况和脂肪链长短或支链化程度的红外光谱参数I3、I4为主要指标,通过BP神经网络分析方法建立了焦炭质量预测模型,并讨论了模型的特点,分析了新模型下的成焦机理。结果表明,使用新的煤组成结构参数预测焦炭质量具有一定优势,成焦率(CR)、显微强度(MSI)、粒焦反应性(PRI)和反应后强度(PSR)的预测值和实测值有较好一致性,对y=x的拟合相关系数分别达到0.986、0.982、0.956和0.926。模型对CR、MSI和PRI的预测效果较好,九个预测样本的平均偏差分别为0.53%、1.58%和1.28%;但对反应后强度PSR预测效果较差,平均偏差在12.22%。研究结果为建立炼焦配煤新方法提供了良好基础。     

Modeling of catalytic coke formation in thermal cracking reactors

At the start-up period, the most important mechanism in the coke production with a clean reactor surface is the catalytic mechanism. The study of this mechanism can be very useful for the better comprehension of the coke production process. In this paper, a model was designed for such a production through the utilization of a catalytic mechanism and a kinetic model, capable of interpreting the catalytic coke production on the reactor surface. For the determination of the model reliability, the experimental data related to the naphtha feed, existing in literature, were used. In addition, the constant parameters of the model, the velocity and the activation energy constants, associated to the kinetic model, were calculated. The results of the developed model were in satisfactory agreement with the experimental data. Eventually, the catalytic coke amount in comparison with the total coke production on the reactor surface and its significance were under investigation.     

Electrophoretically deposited sulfonated poly(styrene-co-divinylbenzene) on a screw for microextraction of cationic dyes from aqueous solutions

In the present work, a novel solid-phase microextraction on a screw (MES) was employed to extract cationic dyes (malachite green, methylene blue, and rhodamine B) from food samples and fish breeding pool water. The sulfonated poly(styrene-co-divinylbenzene) was electrophoretically deposited on the surface of the grooves of a screw. Then the screw was placed inside a silicon tube as a holder to create a channel to run a test solution through it. The extracted dyes on the coated screw were eluted by a suitable eluent. High-performance liquid chromatography with an ultraviolet/visible detector was utilized for the separation and analysis of the analytes. The effective parameters of the analyte extraction efficiency were optimized. Under optimum conditions, the limits of detection were 0.15 μg/L, and calibration curves were linear in the range of 0.50–250.00 μg/L, with coefficients of determination > 0.989 for all studied dyes. The relative standard deviations of intra and inter-day (n = 3) were in the range of 2.8%–7.0% and 7.0%–9.5%, respectively. The MES was applied as a simple and repeatable method with acceptable relative recoveries (82.0%–103.0%) for the determination of cationic dyes in grape nectar, ice pop, jelly powder, and fish breeding pool water.     

镧改性HL沸石在烃类催化裂化催化剂中的应用

 采用离子交换和浸渍相结合的方法制备了La/HL沸石. 将不同La含量的La/HL沸石与REUSY沸石按不同比例复配后作为催化裂化催化剂的活性组分,用标准轻油微反方法(MAT)对催化剂样品进行了评价,考察了La/HL沸石添加量和La/HL沸石中的La含量对催化剂活性、反应产物分布、汽油产品辛烷值及催化剂上积炭的影响. 结果表明,在裂化催化剂中分子筛总量保持不变的条件下,当La/HL沸石加入量为催化剂总量的1%~5%时,随着La/HL沸石加入量的增加,MAT活性和汽油收率增大,比积炭下降; 当La/HL沸石加入量大于10%时,MAT活性及汽油收率随La/HL沸石加入量的增加而降低,比积炭增加. 当加入5%不同La含量的La/HL沸石时,产物中异丁烷含量增加; La/HL中的La含量低于3.5%时,产物异戊烷含量低于参比样品,但随着La含量的增加,异戊烷含量增大. 当La/HL沸石中的La含量为0.2%~0.5%时,汽油中的芳烃含量显著增加,汽油产品的辛烷值提高了1.24~2.06.     

烷基在针状焦形成中的作用

采用煤焦油沥青的甲苯可溶物和废聚苯乙烯共碳化制备针状焦,考察了中间相沥青中烷基含量对针状焦性能的影响。结果表明,通过添加废聚苯乙烯共碳化,中间相沥青中烷基的质量分数从12.0%增加到33.3%,可以制备出热膨胀系数更低、光学各向异性排列更好的针状焦。代表光学各向异性指数的两个量,在光学结构单元中,平行于热膨胀系数方向的轴向分矢量平均长度和光学结构单元的矢量平均长度,分别从20.8μm 和23.4μm增加到28.4μm和28.8μm,热膨胀系数从0.8×10^-6 /K降低到0.1×10^-6 /K。针状焦形成过程中中间相沥青的烷基含量增加使体系黏度降低,有利于光学各向异性相的融并和定向排列。烷基的增多在固化阶段产生足量的气体,在向外逸出过程中使融并中间相的芳香平面大分子沿轴向排列的更为规整。     

Partial oxidation of simulated hot coke oven gas to syngas over Ru-Ni/Mg（Al）O catalyst in a ceramic membrane reactor

Hydrogen amplification from simulated hot coke oven gas (HCOG) was investigated in a BaCo0.7Fe0.2Nb0.1O3−δ (BCFNO) membrane reactor combined with a Ru-Ni/Mg(Al)O catalyst by the partial oxidation of hydrocarbon compounds under atmospheric pressure. Under optimized reaction conditions, the dense oxygen permeable membrane had an oxygen permeation flux around 13.3 ml/(cm2·min). By reforming of the toluene and methane, the amount of H2 in the reaction effluent gas was about 2 times more than that of original H2 in simulated HCOG. The Ru-Ni/Mg(Al)O catalyst used in the membrane reactor possessed good catalytic activity and resistance to coking. After the activity test, a small amount of whisker carbon was observed on the used catalyst, and most of them could be removed in the hydrogen-rich atmosphere, implying that the carbon deposition formed on the catalyst might be a reversible process.     

纳米级稠化剂颗粒沉积膜在乏脂润滑中的作用机制研究

利用双光束干涉法对点接触区乏脂润滑成膜特性规律以及接触区附近润滑剂的微观迁移特性进行了观测.在试验条件下,接触区会经历充分润滑—乏脂—沉积膜润滑—分离油润滑等润滑状态.借助原子力显微镜,探测到沉积膜是润滑脂的稠化剂被碾压破碎而沉积在滚压轨道表面的一层纳米级颗粒薄膜;而分离油是在剪切过程中润滑脂内逐渐释放基础油.试验初始,接触区周围的润滑脂池因乏脂而迅速消失,但分离油会逐渐形成"第二相油池"以实现回流补给.沉积膜增大了基础油在滚动轨道表面的接触角,阻碍回流补给,但其会随运动逐渐磨损,此后分离油将进入接触区补充润滑膜.初步发现,当分离油不充足时,沉积膜有利于保护润滑轨道.     

Fast calibration methods using cosmic rays for a neutron detection array

An overall irradiation and calibration technique was introduced and applied to a test scintillation detector array. An integral conversion method was used to reduce the nonlinearity of the time difference spectrum, and to improve the position determination especially for positions close to the two ends of a long scintillation bar. An overall position resolution of about 3.0 cm (FWHM) was extracted from the residual analysis method and verified by a direct measurement. Energy calibration was also realized by selecting cosmic rays at different incident angles. The bulk light attenuation lengths for the four test bars were also determined. It is demonstrated that these methods are especially efficient for calibrating large and complex detector arrays.     

Rechargeable lithiated silicon-sulfur (SLS) battery prototypes

Amorphous columnar structured silicon film electrodes were prepared and electrochemically tested in dioxolane based electrolyte solution, containing LiNO₃. The electrochemical performance of prelithiated amorphous silicon anodes coupled with sulfur composite cathodes was evaluated in full Si-Li-Sulfur (SLS) cells. The reversible capacity at the first 10 cycles was 600 mAh/g sulfur with gradual fading to ~ 380 mAh/g sulfur after 60 cycles which is the highest obtained capacity reported for SLS full cells. Possible reasons for this capacity fading are discussed.